Air-Cooled Motor 1.5kw ER11 220V D80x188mm Milling Machine Woodworking Carving GDZ-80-1.5 Milling Machine(80x188mm)

MotorsMiddle body diameter: 80*188mmSpeed regulation mode: change the speed through the three-phase output inverter and adjusting the frequency of the inverter.Cooling method: water coolingPower interface: optional YH20-4 pin waterproof . plugs marked "1", "2", "3", "4", "1", "2", "3" are connected to the inverter (U, V, W), and 4 are connected to the inverter Ground the equipment.Power: 1.5kwVoltage: 220vCurrent: 5AFrequency: 400HzSpeed: 24000rpmRunout: less than 0.01mmBearing type: 7005C/P4*2,7005C/P4*13 ball bearingsNumber of phases: 3Chuck: ER11Water-cooled ER11 chuckGrease lubricationMain purpose: used for wood, bamboo, ordinary PCB, PVC, PMMA, plastic, bamboo, two-color board (ABS) and other non-metallic carvings.The working environment temperature of the is usually -10~40.Before installing the first electric to rotate the head by hand, you should feel flexibility and no blockage.P4 fully sealed angular joint bearings can extend the life of the .The longer the length, the greater the and the greater the power.Careful assembly makes the more precise.The accuracy is 0.01mm, and the coaxial cable is less than 0.0025mm1. Our main shaft uses 4 bearings.2. Bearings are to high temperature and low heat3. The ball bearing has low friction, low noise and long service life.When the is stored and transported, the bearing condition inside the high-speed grease will change, and the customer should run it at low speed for 30 minutes. Then increase slowly at a speed of 3000 rpm, running for 20 minutes each time. The and inverter should work together. The specifications and parameter settings of the inverter match the parameters.To connect the inverter main shaft, the three-phase inverter power cord should be welded to the 1 (U), 2 (V), 3 (W) pin, and the grounded pin 4. After turning on the power, observe whether the rotation axis always shows the direction. If it is inconsistent, turn it off immediately, and replace the two wires of the three-phase power supply connected to the inverter and the .Before using the every day, it must run at low speed for 15-20 minutes. Clamp the cutter on the , the chuck nut, chuck, and cutter must be clean enough. The shank inserted into the chuck must be larger than 15mm.The water-cooled must be used together with the water pump. Otherwise, the will quickly break.The AC motor must be used together with the inverter. The power of the inverter needs to be equal to or greater than the power of the . Before use, please set the inverter parameters suitable for the . Otherwise, the and inverter will break immediately.When using the , the noise is different from before, so please stop the immediately. You need to replace the bearing.1. Different cooling methods: The water-cooled motor uses water circulation to cool the heat generated after the rotates at a high speed, and the motor uses fan cooling for cooling.2. Noise: The water-cooled motor is basically no noise, but the air-cooled motor is very large.3. Life: water-cooled motor should pay attention to maintenance, often change water or use industrial water cooler, air-cooled fan mainly blows heat to the heat sink by wind to achieve cooling effect.4. If you need to use metal, hardwood, granite, stone, you can choose metal mandrel. Metal mandrels are much better than wooden mandrels.The frequency power supply is connected to the rated voltage, and the frequency should be consistent with the technical parameters of the electric . The speed can be adjusted to change the frequency, and the voltage changes in proportion.Do not use the , apply compressed air to blow off the static coolant in the pipeline. To prevent rust, please the water hole. The should be oiled. Add anti-wave device and put it in a dry place.To replace the bearing, some professional and technical personnel should be replaced. With special tools, the bearings should be cleaned thoroughly without removing the stator coil.

• Motors
• Air-cooled Motor 1.5kw ER11 220V D80x188mm Milling Machine Woodworking Carving GDZ-80-1.5 Milling Machine